|
Spare Part for
Ensoniq SD1 Synthesizer Music Workstation:
Interface Display, used,
guaranteed non-DOA & functional |
|
Skip down to item's details |
|
Skip down to photos of item |
 |
|
Click any thumbnail for a larger photo! |
|
Item Details |
- This auction is for an Interface Display from the Ensoniq SD1 (32 voice) Synthesizer Music
Workstation. Part is used, but is guaranteed to be non-DOA and fully
functional, or you get your money back, less shipping cost.
- Winner to receive:
- Interface Display from the Ensoniq SD1
- The two interface cables that connect it to the mother board.
- Screws to mount it to the SD1's shell, under the upper side (interface
display area of the casing).
- The two black plastic knobs that control the sliders (shown in place
in the photo above). These snap off for installation of board, then back
on again.
- Easy installation instructions (see below).
- Time required: about 15 minutes.
- Tools needed: Phillips Screw Driver and Allen Wrench
- See the photos below to verify what you will get.
- We have other SD1 spare parts available also. If you need something
beside this auctioned part, let us know and we'll set up an eBay purchase
for the specific part you need.
- Note: All the photos
you see here are
ACTUAL photos of the ACTUAL item.
|
|
Click any thumbnail for a larger
photo! |
|
Interface Display,
used, guaranteed non-DOA & functional
Spare Part for
Ensoniq SD1 Synthesizer Music Workstation: |
|
Below: What model does this part come from? Ensoniq SD1: |
|
 |
|
 |
 |
|
Interface Display,
used, guaranteed non-DOA & functional
Spare Part for
Ensoniq SD1 Synthesizer Music Workstation: |
|
Click any thumbnail for a larger photo! |
|
Below: The "donor" synth, with the interface
display (the part you will get) removed. |
 |
|
Click any thumbnail for a larger photo! |
|
Below: The SD1 synthesizer with the display
interface installed (keys removed in this pic). |
 |
|
Below: The part not only contains the display (seen
at left), but also all the micro switches for all the interface
buttons available on the top of the synthesizer (many shown at right): |
 |
 |
|
Click any thumbnail for a larger photo! |
|
Step 1: To remove your old interface display card, and install its
replacement, first remove the four screws holding down the top, by using an
Allen wrench. Be sure your synth is
unplugged before beginning the process. |
|
Step 2 (shown below): Lift the hinged top of the
synth's shell. The interface display's circuit card is shielded by a piece
of brown card-like paper stock. (It is this way from the factory.) |
 |
 |
|
Step 3: Disconnect the interface display's two connection cables.
These cables provide all the power and communication buses to the interface
display (the cables are shown below). |
 |
 |
|
Step 4 (optional): This auction's winner will receive replacements
for the two cables. You can either reuse your existing cables
(disconnect them from the old display, at the connection points seen above),
or remove your existing cables and use the replacements. To do that,
disconnect the old connection cables from the mother board, at the
connection points seen below. |
 |
 |
 |
 |
|
Step 5: Remove the old interface display.
-
First, remove the two data entry slider knobs on the top of
the keyboard. They just snap off, and then back on after you're done
reinstalling.
-
Then (inside the unit), unscrew all the black screws that
are holding the brown heat shield and display's circuit card up to and
against the underside of the synth's upper shell (some of these screws can
be seen in the photos above).
-
Carefully pull the circuit card and brown heat shield
straight out.
-
Note the tube-like protrusions that have "light tips" (LEDs)
at their tops. When you install the replacement, those will need to be
aligned properly, under and then "into" the buttons they're made to light
up.
Finally, install: Now, reverse the whole process.
You're done! |
|
Click any thumbnail
above for a larger photo! |
|
Other details about the part:
- This part is used.
-
It is in fully functional.
-
It is in very good shape.
- Guaranteed to not be DOA.
-
The SD1 was bought brand new
by the seller, and seller has been its only owner.
-
We will package the part very
well for shipping
-
We guarantee you will get what
we say here in this auction, or else you can get a refund. See refund
details at right.
|
Other details about us, and this
purchase:
-
Check out our overwhelmingly
positive feedback.
-
We have only one negative
feedback in 5+ years on eBay. We can tell you the story if you ever want
to hear it. :-)
-
This part is being sold as-is,
but we will give the buyer 14 days after date received to make sure it
is not DOA, and to compare what
was received with what we promised in this auction. During that time, buyer can request a refund.
-
Damage incurred during shipping
should result in a claim on the shipping insurance, not a refund. In other
words, you would get your money from the insurance, not from us.
-
A refund can be received, less
cost of shipping, handling, and insurance, if:
-
The provided
unit does not live up to what we advertised here, and;
-
You return the
unit only after contacting us first, and;
-
The unit is
returned in the same condition in which you received it, and;
-
You return it to us using the
same packaging we sent it in.
|
|
Payment details:
-
We only accept payment via
PayPal.
-
You get free protection built
into your purchase when you use PayPal.
-
We will ship only to a PayPal
confirmed addresses.
-
We are offering this for sale
only in the USA and for shipment only to residences within the USA.
-
We include very affordable shipping insurance protection
in the shipping and handling cost. We secure coverage for you, so you
don't have to worry.
|
|
For questions about this item or the purchase, contact us
by email at: CACpstr@aol.com |
